Basic problems of your car

How to evacuate and (pulling vacuum on an R134a car AC system)

2012-01-15T08:42:00.015+08:00

Follow the steps below and you will come to see the best result to your aiconditioning system.

1.Turn off the air conditioning in the car and switch off the car engine.

2.Hook up the refrigerant gauge manifold set. The pump hose should be attached to the low-pressure port of the refrigerant gauge. The hose is attached, in simplified terms, to the port that is found in the middle of the gauges. This step is very important in vacuuming the AC system. It helps maintain the vacuum even after the pump shuts down. Refrigerant can be added only after the correct level of vacuum is maintained.

3.Screw the AC vacuum pump to the center valve of the refrigerant gauge manifold set. Keep checking the gauge till the vacuum level reaches 27 Hg. Allow the pump to run for no less than 30 minutes.

4.Close the valve that goes to the gauge. Turn the pump to the off position. Leave the equipment in place, without running the pump for another 30 minutes. After this 30 minutes of idle time, check to see if the vacuum level remains at 27 Hg. If the level is less than 27Hg, then there is a leak in the system that needs to be fixed before moving to the next step.

5.Disconnect the pump hose from the pump and place in a can of refrigerant or freon after the proper of level of vacuum is present and there are no leaks detected. Start the car. Now, turn on the air conditioning system. Open the low-pressure manifold slowly to allow the refrigerant, usually Freon, to flow into the system.

It's like d sideburn of ur car. U've got to keep it shiny & new, to not lose d cool. Chck out #NewLing on #MilkADeal

2011-08-24T11:23:00.002+08:00

It's like d sideburn of ur car. U've got to keep it shiny & new, to not lose d cool. Chck out #NewLing on #MilkADeal

Troubleshoot a car is easy

2011-08-13T07:47:00.003+08:00

Is that so easy to rectify a car problem? It would become easy if we know how to tackle the right problem.For a person who slightly knows technical in automotive it will look easy for them but how about a person who does not know anything about car except sending it to a mechanic?
It is definitely the right way if you know nothing about some thing,is to look for a right person.However there are some cost you have to pay for this.

In other word is if you face a problem and knows nothing about car you must find the right person to rectify it for you.In certain cases for a person who does know a basic knowledge of troubleshooting,my advise is you should not do extra than your knowledge.I have seen a problem whereby i have to do something extra to the car in order to make it fix.Something extra means extra cost you have to pay for a small problem.Do not be smart to what you do not know ,unless you have a guidance and mentor beside you.Get someone who knows about car even though he cannot solve the major problems at least you have a guidance to budget a cost of repair.

A repair cost nowadays is getting higher everday due to price increased in spare parts,engine oil and labour cost.A labour cost is getting higher everyday due to cost of living which is increase every year even month.So to be safe in budgetting a cost for repair is to seek a guidance before you do some thing to your car.Get a right target before shooting an arrow.

Led tail lights for classic cars

2010-06-26T08:10:00.001+08:00

Led tail lights for classic cars

Basic problems of your car(Troubleshooting car problems-Diagnose for a reason

2010-03-08T13:13:00.004+08:00

Why do we diagnose?In fact there are few engine problems need to be diagnose using a machine.In most cases diagnose wouldn't solve anything,it is depend to our experience.I am not denying what machine can do to diagnose and rectify problems but in such cases diagnose machine won't solve anything.If we are solely driving the car sometimes we can know the exact problems by ourselves.

There are few car users tend to send cars for repair without taking a first impression to check first before sending to mechanics or workshop.These will exactly waste time and money for such repairs.We could reduce the cost for repairs if we as a user take a first impression on our car.

We will send cars for diagnose machine for certain reason as below:-

1.-Engine knocking-too noisy
2.-Engine trembles
3.-Engine sign"check engine" is on
4.-Engine idling unstable
5.-Engine wiring malfunction

Those are the few reason why we have to use machine to diagnose the problems.Those problems are exactly direct to engine wiring and system.Small wiring problems such as fuse burn or wire cuts diagnose machine cannot solve the issue.That is why only a certain case the machine will trace the precise problems.

basic problems of your car-Troubleshooting car problems(7 Basic tools and procedures)

2010-01-16T01:57:00.006+08:00

What do we need as a tools and a basic procedures before we go further on troubleshooting car problems?There are a few basic procedures to follow and a tools needed for basic treatment of your car.

Procedures

1)Make sure you have the right place to do repair (workshop or home garage).
2)Make sure you have basic knowledge to do the troubleshooting.
3)Make sure you have a guidance(Books,knowledgeable person or mechanical guide script)
4)Make sure you have the basic tools.
5)Make sure you have the safety(first aid for any injuries)
6)Make sure workshop have protection for any emergency or explosion(fire extinguisher)
7)Make sure you use the right tool at the right place(security for any injuries)

To do a basic troubleshooting car problems is not easy as anyone could imagine.For expertise took years to master such car problems.A basic tools are needed as well as the procedures to follow before taking any job risk.

Tools

1)A socket wrench (complete sizes)
2)A hammer or straight steel(for loosen any hard nut or screws)
3)A floor jack
4)A wire cutter(scissors or small knife)
5)Grease and adhesive
6)Gasket
7)Spare parts

With 7 procedure and 7 tools above you are partially done to do any basic troubleshooting of any car problems .In fact some of those guidance led to do major car problems too.

basic problems of your car-a few engine comparison

2009-10-06T00:08:00.002+08:00

in order to troubleshoot any engine problems,comparison of many engine product are needed.it is also a good troubleshooting guidance for technical expert and also for automotive mechanical juniors.

basic problems of your car-Troubleshooting engine overheating

2009-09-07T17:12:00.004+08:00

Basically there are a lot of troubleshooting process of engine overheating.Before we go further we have to know the car components that works directly to overheating.The components consist of:-
1)radiator
2)radiator fan
3)water pump
4)thermostat
5)water hose
6)water jacket
7)cylinder head gasket

These are the major components always involved in engine overheating.First is radiator,to ensure you will not facing such an overheating problem,radiator must contain enough coolant and absolutely clean from any leaks.Secondly radiator fan must actively working and makes no weird sound at all.Now thirdly water pump,you must make sure water pump still within the limit means it is still can be use without any pouring water from that component.(water pump located inside timing belt
casing)
Thermostat also one of contributors of overheating problems but it is very hard to know whether your thermostat is in good performing level if there is not temperature showing of engine overheating.

Water hose leaks also one of the reason for overheating problems as well as water jacket.You need to confirm of no leaking hose and container at all.

Lastly the cylinder head,this can cause overheating if no water leaking in those water components such as radiator,thermostat and so on.In other word you have to stop driving when your temperature shows engine overheating ,to protect your engine from requiring top overhaul for cylinder gasket burning.

For those all the overheating cause now we can exactly troubleshoot all the problems.
1)take out your radiator and clean it up by filling out the water and fill it back with radiator coolant.Do not forget to check all hose attach to radiator,to ensure no leaks as well as water jacket.
2)You also can check the thermostat by taking out the thermostat and replace it with a new one.(thermostat located at the end of upper hose radiator)
3)If those water components already check please stop driving if your car temperature shows overheating sign.

Basic problems of your car-Troubleshooting No-Start Vehicle Problems

2009-09-02T16:52:00.005+08:00

There is nothing more infuriating than getting into your car only to find out that it would not start. As with other vehicle problems, the causes could range from a mere nuisance to major repairs. However, every driver must know the root cause of the problem and to give it a timely solution.

Murphy’s Law describes all about such situations: whatever can go wrong will go wrong, and at the worst possible time. No start problem could happen when you are already late for work or the car is 200 degrees below zero out. Now, that makes you even more infuriated and you realize that indeed anything that can go wrong will go wrong.

Troubleshooting no start problems would be easy if drivers know its causes. There are common causes and reasons behind the problem. The first reason is the failure of fuel pump failure or the restriction of fuel filter. This is the most prevalent cause of no-start problems in recent times. This is primarily due to the negligence of vehicle owners to enforce scheduled maintenance. Said negligence could be mirrored in part by not having the fuel filter changed at right intervals. Some fuel filters cost $100.00 however in vehicles like the Jeep Grand Cherokees which was built in the late 90s, replacement of fuel pump could cost about $800.00! How many times do you want to spend that much?

One significant cause for premature fuel pump failure is when the driver allows the fuel level to go lower than ¼ tank for extended periods or running completely out of fuel. This will make the electric fuel pump to run dry, which eventually destroys the pump. GMs Vortec engines - 4.3L, 5.7L with the CPI fuel injection system – fail in many ways. Some of the ways include plastic tubes leak, fuel pressure regulator leak, and when poppets get plugged.

engine belting

No start problem could also be attributed to timing belt failure or timing belt tensioner failure. Basically, timing belts are engineered to last approximately 40,000-60,000 miles under normal use. If these belts break, it could result to engine damage. But for vehicles manufactured by Acura, Honda, Mitsubishi, and Nissan brands, the repairs would not be so costly. Moreover, it is recommended that the timing belt be changed at regular intervals. The tensioner should be replaced if questionable.

distributor

Another root cause of no start problems is distributor failure. When your vehicle breaks down without any warning - that could be an indication of the problem. Other symptoms include history of intermittent breakdown and intermittent failure to start from cold, which may be caused by security system failure. Mitsubishi electric distributors in the Ford Probe and Mazda vehicles have a high failure rate.

Electrical trouble is another cause of no-start problem. Ford ignition switches, manufactured in the early 90s, have been known to cause fires. Hence, every driver must check them regularly to shun future bother. One should not only focus on Volvo distributor rotor or Land Rover brake pads; he must inspect every auto part to ensure that it is in working condition.

Batteries, clamps and cables could also cause no start problems. Drivers and owners alike oftentimes neglect corroded batteries. The fact is, batteries do not last forever; do not confuse them with diamonds. Moreover, poor maintenance could result to battery failures that lead to other vehicle problems.

ECM/ PCM failure is also a no-start cause. This problem is common to GM products manufactured on mid 80s. Other causes include inaccurate fuel gauges, lack of oil, plugged exhaust systems, bad fuel injectors, and worn flywheel.

Glady Reign is a 32 year old is a consultant for an automotive firm based in Detroit, Mi. she is a native of the motor city and grew up around cars hence her expertise in the automotive field. You can visit Volvo distributor rotor for more information.

Basic problems of your car-The magic behind Toyota

2009-09-02T16:41:00.005+08:00

Ask a hundred people about what they prefer to own for a car model and chances are majority of the survey respondents would say Toyota. The best thing about owning a Toyota is the fact that the automobile itself is an engineering wonder, built with the best and state-of-the-art engines and embellished with comprehensive electronics and computer software to ensure thecar's even running on the road, no matter what type the road may be.

Of course, such kind of automotive model requires an extensive knowledge of diagnostics and engine analysis to ascertain the car's longevity and durability. While you may have ample and sufficient knowledge pertaining engine repair guidebook, it is necessary to have your Toyotacar undergo a complete engine testing at a professional Toyota repair shop to avoid unforeseen damages that could inadvertently throw you in an accident.

In Atlanta alone, there are several competitive Toyota repair centers that cater to such demand. Among the services they offer are the regular preventive maintenance and computer diagnostics, which allow yourcar to be tested in terms of mileage, engine light, or emission problems.

These Atlanta Toyota service centers also check your car's brake systems to make sure that your stopping power is put to the maximum by checking and replacing brake pods, machining brake rotors, and possible repair or replacement of the hydraulics. Such Atlanta Toyota repair garages may even diagnose the complete element of yourcar's ignition system, whether it's of the traditional distributor or coil type or the recent DIS type.

Moreover, properly trained experts from an Atlanta Toyota service center can also handle the diagnostics of your automobile's charging and lighting electrical systems, the heating, cooling, and ventilation compartment, and the steering component of the engine itself. You can also expect yourcar 's suspension and engine to be properly taken care of after technicians from these Atlanta Toyota repair install new shocks or struts, replace ball joints or wheel bearings, and install or remanufacture engine assemblies.
There's even more in store for Toyota owners because apart from all these services, an Atlanta Toyota service center likewise takes care of yourcar's transmission, muffler and exhaust system, possible auto glass replacements, and even extended warranty repairs!

Of course you can always do basic car troubleshooting with your Toyota but with a great investment such as this, would you risk undergoing unnecessary repairs? Why take the risks when you can always minimize them just by having a regular checkup at these Atlanta Toyota repair centers?

By Mikal Jhonson

Basic problems of your car-Car Maintenance and Repair Tips : How to Install a New Car Battery

2009-07-09T18:05:00.007+08:00

There is no other way to install new car battery,this is the right way and the only one in installing car battery.View this and remember the tips to install car battery.Do not put the wrong side of negative(-) and positive(+) cable of your new car battery.It wil damage your electrical wiring system.If you are not sure of changing your battery get and read DIY troubleshooting car problems here

Basic problems of your car-What does it mean by engine marking

2009-06-15T12:32:00.011+08:00

Engine marking defines as the marking that must be set in order to get a good firing systems to make the engine starts.There are a few components involved such as timing bearing,timing belt,crankshaft pulley and timing belt pulley.

There are a few rules that must be followed to set the engine marking.

1) Must put the upper pulley mark accurately with distributor arm or rotor arm mark.
2) Must put the lower pulley mark accurately with the crankshaft mark.
3) When putting the timing belt clip make sure the upper pulley mark and the down pulley mark still at the same place so that the engine can easily start after installation.
4) Make sure putting the upper and lower timing oil seal properly to prevent any engine oil leaks.
5)Make sure upper pulley tighten properly and close it by timing cover.

Basic problems of your car-Flying Car

2009-06-07T13:08:00.005+08:00

How much gas do we need to fly a car?How to take off in a middle of a traffic jam?Are we going to have a DIY manual of troubleshooting car problems if we purchase one?

Basic problems of your car-Maximize your car service knowledge

2009-06-01T14:10:00.017+08:00

Considering car servicing also part of troubleshooting process in car problems ,we have to be more careful in tackling these service process.As everyone knows it has a specific part to be changed in completing this service process such as engine oil,oil filter and the air filter.However the car user left out a few things that need to be checked and well maintained before they leave any workshop.There are about 10 items need to be checked and also considered as part of servicing process.
Normally in a good workshop service this 10 items being implemented but they never let the car user know and it seems to be not important for everyone to know.

The cause of not taking care of this 10 essentials items car user seldom to have car breakdown even just a few minutes or hours sending for car service.The 10 items are:-

1)Battery water-Never checked or let the mechanic know about the battery water need to be fill up to the appropriate level.
2)Radiator water-This also need to be level up to prevent from more car problems.
3)Timing belt-This has to be checked and taken care off before leaving the workshop in order not to get breakdown.
4)Belting or bearing sound-The sounds of any belting such as alternator belting, compressor belting,power steering belting has to be removed and belting need to be changed if it is broken.
5)Air filter housing-Has to be cleaned and any dirt has to be removed in order to get smooth engine breathing.
6)Water coolant-To skip the engine from sudden heat up water coolant need to be level up.
7)Alternator-In order to get a good car condition after service this one has to be checked.
8)Any oil-Check the oil level such as gear oil,brake oil and clutch oil.
9)Plug cable-change the plug cable in order to get good firing system.
10)Any hose-Any leaking hose need to be replace especially the fuel hose before it cause any burning.

Those 10 items can be 11 or maybe more if this 10, nobody care and the cost of car service and troubleshooting cost also will be higher than what the car user expectation.It will get worst to the mechanic also if this 10 items never been checked by them.

Basic problems of your car-Futuristic Electric Car

2009-05-08T22:56:00.006+08:00

no more gas station?no more petrol?no more haze?It,s really something!How about the parking space?It would be hard to find a troubleshooting manual if the manufacturer do not provide it upon purchase!

Basic problems of your car-Fuel Injectors: Time To Replace?

2009-04-24T23:38:00.007+08:00

When it comes to squeezing out maximum fuel efficiency as well as power from your engine, properly working fuel injectors are an essential component to helping your vehicle run flawlessly. Eventually, however, like any part they do wear out. Fortunately, the selection of stock fuel injectors available on the market is wide; with a little research you can find replacement fuel injectors that are right for your car and at a price that is right for your wallet.

Before you go to the expense of replacing your current fuel injectors, you should first check your fuel filter to see if it is the culprit. If clogged, replace the fuel filter and keep changing it every 25,000 miles. Gas prices are at all time record high levels, but you should only use name brand gasolines containing fuel injection cleaner additives to ensure continued good performance.

In other word this could be done if you have more education on troubleshooting car problems and you could get it on this page,free knowledge to proceed your troubleshooting car problems process.

If after performing the above maintenance your vehicle still isn’t running properly, one or more of your injectors may no longer be working. If you have determined that this is the problems,you will need to replace the malfunctioning injector[s]. If you are seeking better performance, then an after market fuel injector such as an Accel is an excellent choice. If you elect to go the performance route, you must replace all of your fuel injectors at the same time.

One of the leading suppliers of stock fuel injectors is Bosch. In 1967, the German manufacturer introduced the first fuel injection system with a high-pressure electric fuel pump. Bosch is a leader in innovative fuel injection technology and design, as well as in superior, original equipment quality. Yes, many vehicles coming off of automobile assembly lines already come equipped with Bosch fuel injectors: they are simply that good.

Alternatively, Ford fuel injectors, Nissan fuel injectors, and those made by and for other automobile manufacturers are all quite good. They have to be, otherwise their cars would not be able to run!

Prices for fuel injectors are all over the place. It is a good idea to shop and compare before making your purchase. Reputable online suppliers can often give you the best prices; some will even include free shipping making shopping on the internet your best bet.

Matt Keegan is a contributing writer for Car Parts Stuff, an online supplier of high quality and well priced automobile parts.

By Mathew Keegan

Basic problems of your car-Ask your mechanic

2009-01-05T10:15:00.013+08:00

When it comes to car problems and the troubleshooting guidance,user always need someone to ask and find a good solution for their car.
This site link you can discuss anything about troubleshooting car problems as well as searching the car problems guidance .

ASK YOUR MECHANIC,SIMPLY PUT YOUR QUESTION IN COMMENT COLUMN YOU WILL BE ANSWERED 24/7 WORKING HOURS AND DAYS AT THIS PAGE-CLICK

Basic problems of your car-Taking a look at stock car racing

2008-12-31T01:20:00.006+08:00

Stock car racing is one of the most popular forms of racing in America today, as is evidenced by the popularity of the Nascar Nextel Cup. The term "stock car" is derived from the fact that all of the cars used must be original production cars. These cars may be modified for performance, but they cannot be specially designed for racing.

An example of a popular modification is the rear spoiler that is added to every stock automobile used in racing. This spoiler forces the air moving over the automobile to provide enough downward pressure to stabilize the vehicle and provide some degree of protection from overturning during a stock car race.

In car racing sports, a stock car race is normally played out on a track that is oval in design and can be made from dirt or asphalt. There is also the stock car race that is run on roadways, but they are very rare.

The tracks vary in length from the short track, which is approximately one quarter of a mile in length, to the super speedways which can be up to 2.66 miles in length. Maximum speeds on the short tracks can range up to 220 mph; however, the speeds at the super speedways are now restricted to a maximum of 187 mph.

Stock car racing originated with the moonshine runners of the prohibition era. There was such a need to outrun the law when running moonshine that the runners soon began modifying their cars to make them run faster and more efficiently. This soon became a competition between the runners and the early 1930s saw the sport of car auto racing start to become organized. Because the rules for racing were so varied, many wanted more uniformity. In 1948, NASCAR became a reality.

There are many stock car racing circuits other than Nascar. Some examples of these include the IMCA, or International Motor Contest Association, the ARCA, or Automobile Racing Club of America, and the CRA, or Championship Racing Association. These are the "minor leagues" of stock automobile races.

As well as these and the Nascar circuit, you will find other clubs, such as the Craftsman Truck Series and the Busch Series. As in baseball, drivers do not start out in Nascar. They must enter the sport at the bottom and work their way to the top. They must go out and prove themselves and then wait to be invited to drive for a professional car racing team.

A free car auto racing gift awaits you at Mike Selvon portal site, where you can enrich your knowledge further about the stock car racing.

by Mike selvon

Basic problems of your car-What is the Formula 1 car racing

2008-12-31T01:06:00.004+08:00

F1 car racing is another name for the Formula 1 car racing circuit. Some people mistake it for Indy car racing because of the similarity in the looks of the cars. However, this is a different class of sport and the regulations and rules are quite different. The highest class available in open-wheel racing is Formula 1.

This designation was made by the Federation Internationale de l'Automobile, or FIA. The FIA is the governing body over all types of car racing sports internationally. The term "formula" relates to the qualifications that the FIA has for a driver and an automobile to be allowed to participate in this circuit. There are many rules and regulations.

The Formula One circuit is made up of street car racing, which is referred to as the Grand Prix. One thing that is distinctly different about the Formula 1 racing circuit is that there are two championships at the end of the circuit: one for the automobile constructors and one for the drivers.

A race of this type is generally held on a specially built car race track or on a roadway. The road races are perhaps the most popular of the Formula 1 races; the most widely known being the Monaco Grand Prix.

Formula 1 car racing involves vehicles that are modified for optimal performance. The speed that can be obtained in one of these cars can reach 360 mph. On corners, at high speeds, g-force is experienced. The constructors of the cars are members of the car racing team and they must follow a certain set of rules when putting the cars together; however, they are allowed some leeway to modify the aerodynamics, electronics, tires, and suspension to improve performance on the track.

Each of the Formula 1 car racing vehicles is considered to be a single seater. This means that there is no room provided for more than one seat, unlike the stock cars. There are a total of ten teams and twenty drivers each year who compete in the circuit.

The designated engine suppliers for the 2008 season are Toyota, Honda, Ferrari, BMW, Mercedes and Renault. Bridgestone has the contract on the tires for the 2008 racing season. More information about this particular type of sports auto racing can be found at "Formula1".

A free car auto racing gift awaits you at Mike Selvon portal site, where you can enrich your knowledge further about the formula 1 car racing.

by Mike Selvon

Basic problems of your car-Auto body repairs that will save your money

2008-12-31T00:57:00.005+08:00

Your vehicle can last you a long time if you take care of it. In our changing economy right now, you will want to make your current vehicle last a long time. That means you should care for it, keep up with routine maintenance, and take care of any repairs that arise. You may think that only engine or mechanic repairs must be taken care. However, it is important that you take care of auto body repairs as well. There are many auto body repairs that will really save you money down the road!

So many people underestimate the importance of getting paint touch up for their vehicles. Our vehicles paint usually gets small chips or cracks from road debris and other small things that may hit it. Paint touch up will cover those chips and cracks. It is best to take your vehicle to an auto reconditioning shop to get paint touch up since they have the technology to match your vehicles paint for the new paint. Usually it does not make the vehicle look totally better but there is a bigger reason why you get paint touch up. Your vehicles paint is a sealant for the auto body's metal frame. It keeps it from contacting water and other harmful elements which cause rust. You really don't want any rust to form on your vehicle, that will cost you more money and more time versus simply getting paint touch up with is quick and affordable.

Bumper repair is another repair that is often overlooked. It is important that your bumper be in the best shape possible, not all for looks, but because your bumper is what protects your vehicle from further damage and your passengers. So, if your bumper is currently damaged you run the risk of incurring more damage if involved in any form of accident which will cost you much more than bumper repair. Bumper repair is another repair that is quick and affordable.

One more repair that can set you behind financially if you don't get done right away is windshield repair. A lot of times our windshields get cracks or chips from road debris that kicks up on the road. If the damaged windshield is taken in for repair promptly, it can be repaired. However if you wait too long you will have to end up buying and replacement windshield and paying to have it installed which is much more costly than a simply repair. Also some shops will offer a mobile service where they will come to you to repair your windshield.

All of these repairs can be completed at most auto reconditioning shops. They are all affordable and can be completed quickly! But if you don't take care of these repairs quickly you will face the chances of paying much more later and being without your vehicle longer. So, save yourself money and get auto body repairs! Find an auto reconditioning shop near you who can help keep more money in your wallet and get your vehicles looking great!

If your car is in need of auto reconditioning start looking for a qualified professional to handle your concerns. Look for an auto body professional to take care of your ride from bumper repairs to fixing the major auto body repairs.

by samantha Mccartney

Basic problems of your car-Decrease automotive gas and fuel cost

2008-12-26T00:43:00.004+08:00

Your car air's filter is one of the most taken for granted components of your automobile - be it car, truck, S.U.V. or van. Left alone it will do a good job announced - cleaning the engine intake air of dangerous dirt and grime. However ignored a dirty air cleaner can easily slow down and impair your car's performance, acceleration, overall engine running health and easily decrease your gas mileage by 10 % or even more. In these days of high gasoline and fuel costs anything you can save to decrease your overall running costs of your vehicle is money in the bank to you and money in your pocket.

It can be said that overall cars need both a tremendous and enormous amount of air to breathe on a regular ongoing basis. About an astonishing whole 9,000 gallons of air are used up for every gallon of gasoline your automotive vehicle uses. By anyone's reckoning and count that's a large volume of air. It is most important, if not essential for the smooth running as well as long life of your car that the air is breathes is clean, that is free of dirt, dust and grime. This is the job of your "air cleaner".

A breather hose called a "snorkel" actually carries the air from outside the car into the air cleaner. En-route this intake air is heated by hot air that has been redirected from the engine by the pre-heated air-intake system. The air passes through the air cleaner, a container that houses the air filter- which is the workhorse of your vehicles cleanup detail. Most air filters are basically made up of pleated folds of paper, a heavier almost cardboard type of paper, whose job is catch the dirt and grime, which is in the outside air and atmosphere before it can get down into the finely machines engine parts and components of your precious, reliable auto engine.

The air filter in your car can be though of just like the furnace filter in your home furnace. The air filter in your home heating system will clog up with dirt and debris as it is used throughout the year and therefore must be cleaned , maintained and replaced on a regular and ongoing basis as your utilize this machinery. Your car air filter is little different. The difference is that you may be unaware of the maintenance , inspection of and cleaning of air filter of your car , that it needs to be replaced on a regular basis as well and that a dirty or unclean air filter can cost you big money on your fuel bill very quickly.

In the end it can be said that paying attention to your air filter of your car is a very simple matter. When you have the oil of your vehicle changed, or if other work is being performed on your automobile - simply ask the mechanic or maintenance technician to "check the air filter". It's a simple process, in most cases, that is simply done under the hood, with little fuss or muss, and could be done in a second. Either the air filter will be clean and ok , it may be a bit dusty , which a simple blow out with compressed air blowing the dirt out of the filter backwards with a simple whoosh of compressed air or at the worst the air cleaner will be replaced with a new one. Since it's a simple pull out and replace process automotive shop labor repair costs for this process or air filter replacement should be little more than the cost of the new air filter.

Paying attention to your automotive air filter and its maintenance and attention to on a regular basis can be among the easiest and simplest ways to improve your gas mileage, reduce your automotive fuel costs, improve engine performance and improve engine life and reducing repairs. It's all about maintaining your automotive vehicle to improve reliability, life of your vehicle while leaving you with extra cash in your pockets.

By terry e voster

Basic problems of your car-Maintaininig your new car

2008-12-26T00:32:00.009+08:00

There is no joy quite like the joy that comes with getting a brand new car. It's an exciting investment that appeals to all of the senses. It looks good, sounds like a kitten and smells brand new. So of course you may naturally assume that a brand new car doesn't need maintenance the same way an older car does and you would be correct, for the most part. But a new car needs to be taken care of if you want it to last long enough to become your old faithful road warrior.

All new vehicles come with a user manual that explains all of the ins and outs of the vehicle. It will also tell you how often certain services need to be performed like oil changes. Get acquainted with this manual. Even if you don't read every page, flip through it and pick out the most important points. The index will be able to direct you to any page so keep the manual in a place where you can always access it easily.

Oil changes should be performed every three thousand miles or every three months to prevent car problems while driving. Ask your dealer for any additional information or any basic troubleshooting car problems manual if they not automatically supply it. It's important not to go over this limit and ignore the need for an oil change. As oil gets dirty, it can slow down the engine and make it feel bogged down or run rough. Get your oil change on time so it continues to purr like a cat.

There are other things that you need to keep on a maintenance timeline as well. You must make sure the tires are rotated as necessary for optimum traction on the road. You also need to check all of the fluids in the car on a regular basis. Even if they don't need to be refilled or changed, you need to know they are all as they should be. From transmission fluid to brake fluid, there are a lot of things to stay on top of. Check all of the fluid reservoirs as well to make sure there is no damage or possible leaks.

Keep your engine clean by using cleaners that are designed to be used under the hood of your car. As the engine gets dirty it can become clogged up with oil spills and dirt. A clean engine will run much better and has a good chance of having fewer problems as well as reducing cost in troubleshooting. It also makes it much easier to identify a new car problems.

Get a car wash regularly to maintain the exterior appearance of your new ride. The road is filled with dirt, oil and salt. These things can eat away at your paint job which leaves hideous results over time. Keep your paint brand new with a car wash once a week. Give it a good wax every quarter of a year at least as well to protect your clear coat.

When it comes to maintaining your new car one of the best things you can do is to drive it with care. If you blast around like a maniac and lay on the gas a lot, you will put your engine under unnecessary stress. Love your car and it will take care of you.

By Levi Quinn

Basic problems of your car-To identify the problems

2008-12-20T08:51:00.011+08:00

After 15 years involved in automotive industry I discovered a few basic car problems which i would like to share.With a few simple tools everybody can start repairing their own car such as screwdriver,wire tapes etc.This troubleshooting car problems process would be necessary if you need one or otherwise you can just send it to car service center.

Warning:If you are not sure of doing it yourself please get an expert to do it for you.Troubleshooting car problems process won't be easy if you have a guidance and your intention of doing it yourself.

Ist problem-Engine cannot start

If this happen please check the if the battery has been properly connected and it's still in use.If it is done please check the sparks using another spark plug and connect with the plug cable touch it to the engine body while the other person crank the engine.It is to check whether the firing condition is on.If there is no sparks comes out it must have a problem in engine wiring or the plug cable itself.

2nd problem-Engine temperature goes up

If this happen you can check the water system of the car by checking the radiator hose and water pump for leakage.It is to make sure no leaking hose and any leakage can be heal by changing the component.If you have a radiator leakage,after replacing raditor must be tighten up properly to prevent any leakage in future.
If you have a water pump problem please ensure that after replacing the 'engine marking' is in order to prevent any engine knocking so that your car is easy to start.

3rd problem-Engine start but make a lot of noise

It is advisable to check whether the engine has enough oil. With not enough engine oil engine knocking will be more and you can easily hear the noise.

Air filter also has to be changed in order to keep the ratio of air and fuel is in good ratio to prevent your car easily get heat up.

4th problem-weird engine noise

It is always happen when the engine oil gets to thick due to very long usage.This could be heal when you change the engine oil.

5th problem-The car cannot move

You must check the gearbox in order to make sure the clutch plate still can be use.If is already expire please change the clutch plate and also the gear oil.

Find more knowledge on troubleshooting car problems

Basic problems of your car-1st level-To know the components of your carBasic problems of your car-

2008-12-20T08:42:00.012+08:00

This is a pre level in automotive repair before proceeding to the next level of repairing a car.In this pre level is about to know the car components and the use of those components.This is the most basic level and the most important part to know before touching any tools in automotive repair.I am about to explain a few basic car components such as below:-
1.Spark Plug-The use of spark plug is to bring a sparks in firing system of the engine before the combination of fuel to make the engine starts.

2.Battery-To start the engine a car must have a battery just like a remote control items which has this component too.
3.Starter motor- This component is a mechanism to make the gearbox flywheel spinning in order to on the engine.
4.Firing distributor-In order to distribute the sparks, engine must have this as well as the spark plug cable before the engine can run.There 2 types of firing distributor which are electronic and non electronic firing distributor.
5.Plug cable-It is an important part to make the sparks distributed to all the spark plug and the engine can run on their own consistently.
6.Ignition coil-this is a mechanism to keep the sparks energy and it goes along with distributor to spread the sparks all over the engine using a plug cable.

All above are the basic components of firing system in any vehicle engine.

Now we move to the fuel system of a car.It is very important to know that fuel is a main component also in engine system,without fuel the engine cannot even run and the rest of engine components also cannot play their role.

1.Fuel pump-To spread the fuel to carburator or injector we need this component to suck fuel from the fuel tank.
2.fuel filter- To filter fuel from dust or any tiny items from fuel tank after reaching a fuel pump.
3.fuel tank-It is tank to keep the fuel and always located at the bottom of a car.
4.Fuel injection-as a new technology in automotive fuel system after carburator this components act as an injector to to maintan the ratio of air and fuel in keeping the idle system of the engine to run.
5.Carburator-the old fuel system now being replaced by fuel injector and the role still the same.

Basic problems of your car-How to adjust car tyre pressure

2008-12-19T09:07:00.006+08:00

Having the right tire pressure is crucial to driving performance. It is as important as having water and oil in the car, but it is often neglected because it is out of sight and out of mind. There are no flashing lights to let you know when your tire pressure is too low or too high, so it is up to you to stay on top of it.

Failure to ensure correct tire pressure can lead to:

Decreased Fuel Efficiency

This can be a killer in today's economy. Adjusting your type pressure is a free way to make your fuel go further, and it only takes ten minutes at your local gas station.

Premature Wear

Unless you've got money to burn you're not going to want to buy new tires more often than you have to.

Accidents

A blowout, or a loss of grip caused by prematurely worn tires can lead to fatal consequences.

How To Check Tire Pressure

Step One

Ascertain what the correct pressure for your tires is. This information can be found on the side of the tyre. Tyre pressure is often expressed in an acceptable range of pressures rather than a single specific number. Filling your tires to the lower end of this number range will give you greater grip by making your tires a little 'softer'.

Step Two

Your tire stems will have rubber caps on them. Remove these before attempting to change your tire pressure.

Step Three

Set the gauge on the air compressor to your desired number.

Step Four

Connect the nozzle to the tire. You will hear a rush of air when it first connects. This should stop when a seal is formed.

Step Five

Let the air compressor do its thing. When your tire is at the correct pressure, remove the nozzle swiftly.

Step Six

Screw those rubber caps back on the stem, repeat three times, and drive safely.

By Roger rager

Basic problems of your car-How to replace a fuel filter

2008-12-19T09:04:00.005+08:00

If you are looking at how to replace a fuel filter for a Toyota Camry, or any other popular brand of Toyota, you have come to the right place. Before we get started on the steps to changing this fuel filter, you need to first take into account these warnings. First of all, you need to wear eye protection. You will be working over your head, and you do not want dirt to fall into your eyes. Second of all, you are changing the fuel filter, so gas is going to be involved. You do not want to get gas in your eye. If you do, you need to rinse your eye with clean water for about 15 minutes. Last, but not least, try not to breath in the fuel. Studies show that this can cause cancer.

Steps to Changing the Fuel Filter

First of all, you have to purchase the replacement filter. This can be done at pretty much any auto parts store. You will need the make and the model of your car. For example, if you are replacing the fuel filter on a Toyota Camry, you will have to let them know. Next, you need to locate the position of the old filter. Depending on your make of Toyota, it could be located in a few different locations. Sometimes it is by the engine compartment, and sometimes it is under the car by the fuel tank. To make this job easier, it is best to look up your car model online and find out where it is located.

Next, if the manufacturer recommends it, you should remove fuel pressure. After that, you will want to unscrew each hose clamp that is holding on the hose. Most of the time, they are held in place by a bolt unit. Be sure to keep this bolt and the nut together. After removing the clamp, it will be time to remove the old filter and replace it with the new one. After putting the new one on, you will want to then clamp it down with the clamps that you loosened earlier.

The next step is the one that you have to follow very carefully when replacing a fuel filter. After attaching everything, you need to run the engine. During this time, you need to look and see if you can find any leaks. If you see a leak that means that the clamp is not on tight enough. At this point, you will want to stop the car and go back and tighten the clamp. Also at that time, check to make sure that you have the fuel filter all the way on.

After doing that, you are done. Once again, check the car by running it first before you go off driving. You would hate to be out somewhere and the hose come popping off. You could run out of gas in seconds if that was to happen, and there would not be much you could do about it.

A Few Tips to Remember

Changing a fuel filter on a Camry, or any kind of popular Toyota, is pretty easy. However, there are a few tips that you should check out and remember before you get started. First, check to make sure your rubber hoses are not cracked. Since you are going to be down there anyway, it could be a good time to replace the hose if it is way too stiff. Not only that, but you are going to want to pull off the old fuel filter and put the new one on in one quick motion. The quicker you do it, the better. This will be able to help you avoid losing a lot of fuel on the ground. If you are afraid that you cannot do it quick enough, then you may want to clamp the ends of the house. If you have any questions about what to do that, or if it's your first time, your best bet would be to talk to the people at the auto shop before you get started. See if they can give you any good tips as well. A lot of the people in these shops have been taking care of cars for a long time, and they know some good tricks of the trade that could help you.

Mantius Cazaubon is a successful author and publisher of Toyota Parts Buyers Guide A resource which includes information on Discount Auto Parts and Do It Yourself Auto Repair

By Mantius Cazaubon

Basic problems of your car-How to replace your brake pads

2008-12-19T09:01:00.005+08:00

There are a lot of different kinds of cars out there, but most of them have the same steps to changing their brake pads. Today we are going to talk about how to change brake pads on the most popular Toyota cars. A lot of people do not like to spend the money to get their Toyota Highlander some new brakes, because it costs a lot to go to a shop to do that. However, when you are driving something like a Highlander, you want to keep the brakes in tip top shape. That is why it could be a good idea to learn how to do it yourself. The brake pads are not the easiest thing to change on a car, but most of the time, people seem not to have too hard of a time with it.

Steps to Changing Your Toyota Brake Pads

First of all, you need to jack up your car, and make sure that it is supported. This is because you are going to have to take your wheels off to be able to change out your brake pads. The first thing you will need to do is to take a screwdriver and remove your wheel cover. If you do not have a hub cap, then you can move on. After taking off the cover, you will need to take your wheel off by using your lug wrench. Most of the time, cars will come with this. After doing this, you will notice that your caliper, as well as your brake rotor, are now exposed.

From here you can take out the pins or the bolts using your socket wrench. After doing this, you can simply lift the caliper off and away from your brake rotor. Please note that you should not allow the caliper to just hang by its rubber brake hose. Doing this can cause a lot of damage to your caliper. At this point, you may want to inspect your rotors to see if they need to be replaced as well. Check for cracks, as well as any kind of gouges, that could be in it. After checking that, you will want to remove the worn out brake pads from the caliper, which you have not left hanging, right? You will need to remove both of the brake pads that are on the caliper. One is called the inboard and one is called the outboard.

After removing the worn out pads you can put the new ones on. You have to be sure to install the pads on the correct side of the caliper. A good way to tell if you are putting them on the right side is to check to make sure that your outboard is the pad that has a wear sensor on it. This is the thing that sounds really bad whenever your brake pads are almost gone. After putting them on the right side, then you can add back in the clips and all the pins. Sometimes it can be hard to get the pad into place. Do not be afraid to wiggle it into place if you have to. Then you simply just reverse everything that you did. Put back on your rotor if you took it off, and then reinstall your caliper to its mount spot. Make sure everything is tightened and secure as well.

Finishing the Job

After doing all of that, you can put your wheel back on and tighten it securely. Then put your wheel cover back on and lower your car down to the ground. Before you start driving, it is a good idea to turn your car on and pump your brakes a few times to reset your calipers piston. When it is fully set, you will notice that the brake will become harder to press. When you first go to press it, you may notice that it is very lose feeling and your foot goes all the way to the floor. However, after a few good pumps on the brake pedal, you should be good to go.

Mantius Cazaubon is a successful author and publisher of Toyota Parts Buyers Guide A resource which includes information on Discount Auto Parts and Do It Yourself Auto Repair

By Mantius Cazaubon

Basic problems of your car-Changing an oil filter

2008-12-19T08:56:00.005+08:00

Looking at an oil filter, one might think that is an easy device to change. However, changing one can be difficult exercise. Changing an oil filter is mandatory if a person's engine is to last for a long time, therefore it should be done correctly. Many factors affect the ease with which an engine oil filter can be changed. The location of the oil filter really matters; some are usually kept in places one cannot reach easily. The degree of tilt used in the mounting of the oil filter in an engine can also determine if one will change the oil filter with ease if they will have trouble. The manner in which the it was installed also determines if one will have an easy time while replacing the filter or not. Another factor that can affect the ease with which a person will change an oil filter is its size, which can be either too big or too small.

The first step in changing an oil filter is to look for a wrench. Ideally, one can unscrew an oil filter using their hands however, after sometime, oil filters become coated with grease and oil, which can make it difficult to unscrew them. Apart from the grease and oil, People usually put on oil filters tightly and a wrench may come in handy to unscrew them. There are special wrenches available for the task of unscrewing oil filters. Such wrenches are like the chain wrench, socket wrench, strap wrench and sleeve type wrench. The clearance around a car owner's filter usually determines the kind of wrench they will use. Sleeve type wrenches are the best because of their long hands, which add leverage. The next step is to put on work or latex gloves because the exercise is likely to be messy. Wiping the filter using rags or paper towels is the next step. This helps to remove most of the grease or oil, which helps the wrench to grab.

The next step is to place a container such as a drain pan, basin, plastic bowl that oil from the filter will drain into as soon as it comes loose. One should then turn the oil filter with the wrench until one can take it by hand. The oil will start running on the filter's side and once it is off the threaded post, one should invert it inside the container so that the oil can drain out. One should then wipe the plate or post used for mounting the filter and take out the new filter. Then they should spread drops of new oil over the rubber gasket's entire surface. Finally, one should screw the filter on the posts and then run it up towards the gasket plate. After it has snug up, they should turn the oil filter an additional ¾ turn to tighten it. It is advisable to read instructions on oil filters as some may need more tightening.

Have a fun and safe time on the road, and visit us to find the best deal on the auto insurance coverage you need. Get money-saving tips, free auto insurance quotes and helpful car insurance advice at http://www.AutoInsuranceRatesDirect.com today

By levi Quinn

Basic problems of your car-Save Money - Do Your Own Automobile Maintenance

2008-12-19T08:53:00.003+08:00

Most automobiles manufactured today are expected to reach its 200,000- mile mark with regular maintenance and tune-up. Prices of automobiles are consistently increasing. To ensure that your car performs well, to preserve your investment, save yourself tons of money and effort, have your car repaired by an auto technician.

The key steps are to choose quality parts and keep your tools on hand to perform check-ups and routine maintenances for your auto.

Learning More About Your Automobile

If you want more information about your automobile, the best place to turn to is the owner's manual. Take note of maintenance procedures according to your car's mileage:

* 3000 miles

Whenever you reach 3000 miles, you need to change the engine's oil. As you do this, you need to change the filter. Other aspects to look into are the fluid, tires, air filter, hoses, and belts. You must examine the state of battery cables and terminals.

* 5000 - 10,000 miles

Maintain the rotation and balance of your car whenever you cover 5 to 10 miles. This will ensure that the tires won't wear out and its life span is extended. Take note, most especially, of the front tires for the right pressure.

* 15,000 miles

Change air filter after running 15,000 miles for fuel efficiency. When your air filter is dirty, it will cause damage to the engine. As you do this, take time to also check your brake system.

* 30,000 miles

Once you've reached 30,000 miles, check your transmission's fluid level. Consult your owner's manual for the right kind of fluid to use in your car. Use the manual for proper directions on how to properly drain and change fluid.

* 50,000 miles

Upon reaching 50,000 miles, you need to change your car's coolant. Also, maintain your car's finish to ensure it remains in good condition. Constantly wash and apply wax onto your car as varied weather conditions could diminish the paint.

Car Maintenance Software

To ensure that proper maintenance is done on your car, you need to keep records. There are several ways to keep your records whether it be in a separate notebook, a log, or in your computer. In fact, there is a software available for this specific function. This particular software contain programs that track such maintenance procedures as repairs, replacement of parts, and fuel consumption.

The software can be used for monitoring multiple vehicles. Hence, you will know when one vehicle needs maintenance or changing of parts as it often becomes much of a hassle to keep track on each one.

Another impressive feature for this software is the capacity to set service schedule and reminders on when the next maintenance will be performed. Aside from that, it offers practical car care tips for your vehicle. Lastly, there are diagnostic and reference tools in case you have trouble with your vehicle.

Diagnose Your Vehicle

There are common car problems that require only simple job. Instead of going to a technician, you can save money by doing it yourself. Below are a few tips for fixing common car problems you can do.

- When you turn on the ignition and the car does not start, the battery might be dead. Often, this is due to an interior light being left on. Look for this light so you can turn it off. Wait for a few minutes and try turning on the engine again.

- When you turn on the ignition and you hear a screeching sound, you might need to check the fan belt. In fact, you might need a fan belt replacement, which is something you can do. However, if you are unsure on how to do this, you can always seek the help of an auto technician.

- There are certain instances wherein the car starts but dies after a matter of seconds. This might be due to fuel getting into your engine tank. There are 3 possible reasons for this: you are using the wrong type of fuel, you are out of fuel, or there is something wrong with your safety switch.
Do-It-Yourself Auto Jobs

While there are car maintenance procedures you must leave to the auto professionals, it is your duty as the car owner to check on the condition of your vehicle. Here are a list of basic car maintenance techniques:

1. Maintaining wiper blades.
2. Providing wiper fluid.
3. Changing oil and checking oil filter.
4. Checking tires for right pressure.
5. Maintaining headlights.
6. Checking air filter.
7. Replacing spark plugs.
8. Checking battery life.
9. Keeping an eye on automatic transmission fluid.

Are You Suffering Due to the Economy? Does the Current Downturn Make Stretching a Dollar Impossible? Are You Wishing You Could Get Some Relief? Survive The Bad Economy By Learning How You Can Cut Costs And Come Out On Top! Visit Our Website To Find Out More About Surviving The Bad Economy.

By Frank Ramsey

Basic problems of your car-The major brake system problems

2008-12-19T08:27:00.003+08:00

Its Monday again and the weekend is over. How was this weekend for you and did you drive a lot? Was it a smooth drive or you faced some problems with the brakes of your car. You must have felt the change if you have followed the DIY tips to change your car's brake pads.

Brake system form an essential part of an automotive engine. Regular maintenance and check of car brakes is very important in order to ensure your safety on road. There are a number of problems that you might have faced with car brakes. Lets discuss some of the common ones.

Wear of the Brakes - One of the most common problem is the wear of car brakes. This is obvious and natural coz auto brakes are frequently used and do a lot of work. The brake pads of your car are consequently working hard as well. This leads to the wear of the brakes.

Squeaking or Grinding - Excessive usage of brake pads leads to their wearing down. You might notice brake problems like squealing or increased stopping distance. Most of the cars have brake pads with a thin metal tab. When you brake pads wears down, this tab vibrates against the rotor which might damage it.

Sounds of Wear Indicators - At times, the dust of brakes can be the reason behind some kind of sound or squeaking. This is a minor problem with the brake system and you can easy do without it by cleaning the dust. Using a brake cleaner spray is an easy way to do so.

Rotors Might Warp - Often, you yourself must have felt the problem of facing warped rotor or heard you neighbor facing this problem with his new car. Warping of rotor is a common problem which might happen because of overheating. The other reason for warped rotors can be incorrect tightening of the wheel.

Thin Rotor Wrap Easily - I have heard a number of car users facing warped rotors problem with their new cars. This is so because the new cars have thin rotors that get warped easily. This problem can be rectified by repairing the rotors or by replacing them. Please ensure that you consult an experienced car mechanic before doing so. It is also important that you should understand how brake system work.

Loose Lug Nuts After Repair - This is crucial and can be dangerous also. If you have got your car brakes repaired and the lug nuts are not tightened, it can damage your car brakes. Ensure that the nuts are tightened evenly so that the rotor doesn't warp. It is important that the care repair mechanic uses a torque wrench.

These were some of the common problems that you often face with your car brakes. A little care and few preventive measures will help you avoid these problems easily. We'll find out few preventive measures and DIY tips to keep the car brakes and the entire automotive brake system of our car functioning at its best.

I am Fred Clay, a journalist and an automotive industry expert. Automobiles, automotive parts & components and any & everything related to this industry interests me and is my passion. Over the past eight years, i have covered different automotive industry related news and have been writing on the same. As a professional I have reported on myriad topics, my favorite is the automobile industry. I also write for different web portals and websites. Amongst all, my favorite is Automotive Components & Parts that is an Automotive industry B2B marketplace. This portal - Automotive-online.com provides detailed information on industry overview, news, trends, professional associations, publications, tenders, product catalogs, international trade leads, trade events, worldwide manufacturers & suppliers related to global automotive components & parts industry. I now blog at: Automobile Hotspot

By Freddic Clay

Basic problems of your car-Service your own car

2008-12-19T03:38:00.003+08:00

The benefit of servicing your own car is to save money, and let's face it in today's current climate of rising fuel and garage costs we can all save money by carrying out some basic servicing essentials. The following basic guide has step by step instructions that will give you the information on how to give your car a basic engine service including oil change, oil filter, fuel filter and spark plugs.

Please note that the following is meant as a guide for the standard petrol engine only and therefore should not be relied upon as fact as all vehicle manufactures differ.

Equipment Required

• Oil-drain plug spanner / suitable tool.

• Oil-filter pliers / suitable tool.

• Spark plug spanner / deep socket with extension bar and ratchet.

• Jack and axle stands.

• Oil drain pan.

• Clean rags.

• Safety gloves.

Oil & Oil Filter Change

The engine needs to be warm before starting these procedures as this will allow the oil to drain more freely.

1. Raise the front of the car with the use of a jack and then support with axle stands.

2. Using an oil drain plug spanner or a suitable tool, loosen the oil drain plug at the bottom of the sump and using an oil drain plug spanner or suitable tool slacken the plug approximately half a turn.

3. Position an oil pan directly under the drain plug and remove drain plug allowing the oil to run, be aware that it may take some time for the oil to drain completely.

4. Clean the drain plug and sump using a clean rag then refit the drain plug securely, ideally fit a new sealing washer before refitting plug.

5. Move the oil pan and position it under the oil filter.

6. Using oil filter pliers or a suitable tool loosen the oil filter then unscrew it by hand and empty the oil into your oil pan.

7. Wipe away all oil from engine-filter area with a clean rag.

8. Apply a light coating of clean engine oil to the new filters seal and screw into place firmly by hand.

9. Once you have removed everything from under your vehicle lower the vehicle to the ground.

10. Unscrew the oil filler cap positioned on top of the engine and pour in the specified grade of oil for your vehicle. Continue to do this until oil reaches the top mark on your oil dip stick and refit filler cap.

11. Start engine and allow it to idle for a couple of minutes.

12. Turn off engine and check for any leaks, allow the engine oil to settle for a few minutes then check the oil level at the dipstick again and top up as required.

Changing the Fuel Filter

The position for the Fuel filter vary on most cars however the most usual places are in the engine bay or under the vehicle usually close to the fuel tank.

1. Remove the strap that holds the filter in its position.

2. Look for the direction of an arrow on the filter (when available) and disconnect the fuel lines / hoses from filter and remove (please note that fuel may be spilt on removal). Prior to removing the fuel lines you will need to block the fuel lines using a small pair of mole grips or something similar.

3. Put the new filter into place and refit fuel lines / hoses.

4. Refit fuel filter into its original position securely fastening it back.

5. Start engine and check for any leaks, don't be disheartened if it doesn't start first time as the fuel takes time to circulate initially.

Changing the Air Filter

1. Disconnect all vacuum and breather hose pipes from the air filters housing.

2. Remove all retaining clips and open filter housing.

3. Remove the filter.

4. Fit the new air filter into its housing ensuring that it sits in its correct positions.

5. Refit the filter housing and securely tighten using the original screws or clips.

6. Reconnect all vacuum and breather hose pipes back up to the air filters housing.

Changing the Spark Plugs

It may be necessary to remove other parts to enable you to gain access to the spark plugs. Refer to your owner's manual if unsure and always change spark plugs one at a time.

1. Clean the immediate area around the spark plugs clean using a clean rag.

2. Remove the spark plugs (HT) lead.

3. Carefully remove the spark plug using a spark plug spanner or deep socket with extension bar and ratchet.

4. Carefully fit the new spark plug ensuring that it is securely tightened.

5. Refit (HT) lead making sure you have made a good contact / connection.

6. Repeat the above steps for each individual spark plug until complete.

Author Andrew Whitehead - a self confessed petrol head has owned numerous classic cars from fully restored to basket cases!

Basic problems of your car-Car Parts - Quality, Servicing, Maintenance, and Replacements Are Essential

2008-12-19T03:12:00.003+08:00

But this is not the case. A car like any other machine is made up of hundreds of Car parts that work together to make a car run. All of these parts are crucial to the proper working and smooth running of a car. It may be as trivial as a screw or nut in the Car Engine or Car Gearbox. A loose nut or screw can not only hamper the smooth running of the car, it may even prevent the car from running at all. If it is a crucial nut or screw, such as the ones used in the Wheels of a car, it becomes more essential that they be properly fixed. The Quality, Servicing, Maintenance, and or replacement of Car parts over a period of time is essential and crucial for the proper running and long life of the car.

Timely and proper Servicing and maintenance of a Car and Car parts ensures a longer life for the car with problem free driving. Properly servicing and maintaining the car, with timely replacement of parts with Quality spare parts, ensures that the car does not ditch you when you need it the most, especially in an emergency. One of the most crucial parts of a car, besides the brakes and Car Engine, is the Car Gearbox system. A serviced and maintained Car Gearbox ensures a smooth ride. The opposite of this, a poorly maintained and serviced car and gearbox could be a nightmare ride, with loud noises and bumpy rides. An improperly working Car gearbox could sometimes seem like a giant gnashing his teeth in rage. If you ignore the Car Gearbox and not attend to it in time, you may very well have to replace the whole gearbox in order to use the car.

Quality Car parts, timely servicing and maintenance, and or replacing parts with good quality spare parts is not only essential, but crucial to the smooth running and long life of a car. If you can think of a car as a living, breathing object, then you can understand that just like any other animate object in this world, a car also requires food (oil and gas), servicing and maintenance (washing, oil changes, etc), or some tuning and adjustments of parts (heart surgeries, liver, lung, and stomach ailments) and sometimes replacement of parts (liver transplants, heart transplants). This just shows that if you take care of a car like a family member, it will provide trouble free service for years and be with you like a friend for life.

Please do visit our website or write to us for more information on Car Parts or Car Gearbox and for all Car parts and spares

By Sunil Punjabi

Basic problems of your car-How to Clean Your ABS Wheel Sensor

2008-12-19T02:59:00.003+08:00

Does your ABS light come on consistently and you do not know what is wrong! Well, when you check your code, you may see that it says that your front wheel sensor is damaged. However, that is not always the case. A lot of times, your ABS wheel sensor is just fine; they just need to be cleaned. Of course, if you take it to a shop, they are going to tell you that you need a new one. So we are going to go over how you can clean your own ABS wheel sensor in your Toyota and save yourself a lot of money. After you clean it, if you are still having the problem, you will need a new one. However, most people have noted that nine times out of ten, this does indeed fix their problem.

First of all, before you get started, you are going to want to make sure you have everything that you need to perform the job. The only things that you are really going to need are a ratchet, jack, wheel lock and, of course, a rag or paper towel to clean it off with. After you have all of this stuff, you can feel free to get started. This should only take you an hour or two to do yourself.

Getting Started On Your Wheel Sensor

First, you have to choose which side you want to get started on. You can choose either the passenger side or the driver side; it does not really matter. However, whichever side you do choose, that is the side that you, of course, need to jack up first. Before you jack up the car, you need to turn the steering wheel to the opposite side that you are working on. For example, if you are working on the driver side, then you are going to want to turn the wheel to the passenger side. Also, when you get it jacked up. You should use a jack stand, not just the jack. You never know how long you will need to have this car jacked up, so you will want the jack stand.

After you turn the wheel and get everything all set up, you will notice that you should be able to locate the ABS wheel sensor very easily. It should be located directly mounted to the knuckle. To take this off, you are going to have to remove the two bolts that are holding them in place. In most Toyota cars, they are 10mm bolts. However, some of them can change from time to time. Overall, there will be about four bolts you have to take out. To do this, just follow the ABS sensor around so that you can remove all of the bolts. When you get the sensor off, you will notice that it is all covered in dirt. Take your rag or paper towel, and start whipping it off. As you do, you will notice that the very middle of it has a sliver strip that you could not see before. A lot of times, dirt blocks this and can cause problems, as you found out. After cleaning it, simply reverse the steps you did to reinstall it. Also, be sure to check both of the front ABS sensors. The one on both sides of the car!

Still Having Problems

Most of the time the procedure discussed above will fix any problem that you are having with your ABS sensor. If you have cleaned both of the front sensors and there are still problems, then you do have a damaged ABS sensor. At this point, you need to get new ones and replace them. If you want, you will be able to install them the same way you cleaned the other ones. However, instead of cleaning the old ones and putting them back on, you can simply put on the new ones. Overall, this is a one day job that can save you a ton of money. Most people do not notice how much money that they can save by doing this themselves until they actually do it!

Mantius Cazaubon is a successful author and publisher of Toyota Parts Buyers Guide

A resource which includes information on Discount Auto Parts and DIY Auto Repair

By Mantius Cazaubon

Basic problems of your car-5 Benefits of Wheel Alignments - Why to Get Your Wheels Aligned Regularly

2008-12-19T02:56:00.003+08:00

Regular wheel alignments are an important part of conscientious car maintenance. Unfortunately, many car owners fail to understand the importance of good wheel alignment, and therefore don't have their alignment checked often enough.

Here are five reasons why getting regular wheel alignments is good for your car, your bank account, and your peace of mind.

1: Better gas mileage. When your wheels are aligned properly, it cuts down on rolling resistance, which means that you car doesn't have to work as hard or burn as much fuel in order to move forward. This is good news for everyone: Not only do you spend less money on gas, but you also get the satisfaction of knowing your car is responsible for less pollution.

2: More mileage out of your tires. Even the slightest problem with your alignment can have disastrous effects on your tires. If your tires have too much or too little toe-in (the degree at which they point in toward each other at the front, like a person who stands pigeon-toed), a narrow strip on each tire will wear down very quickly, causing you to have to get new tires sooner. By getting regular wheel alignments, you ensure that your tires wear evenly, making them last as long as possible.

3: Tire warranties still apply. The problem with your tires wearing from poor wheel alignment is that it usually voids your warranty on the tires. Most warranties only apply to the quality of the goods. In other words, if the tires wear out too soon because of something other than poor quality, then the manufacturer is not responsible. Failing to get wheel alignments often enough is considered to be negligence on the part of the car's owner, and usually means that the warranty is voided.

4: Less wear and tear on other parts. Having the wheels out of alignment can be stressful on the rest of the car, too. It means that you continually need to put pressure on the steering system in order to keep the car straight, and when you brake you often feel the car pull even more sharply, indicating that the brakes are needing to work harder on one side than the other.

5: Easier to drive. One of the biggest advantages of having your wheels aligned properly is that your car is easier to drive. No annoying pull to one side or the other. It's much easier and more pleasant to drive a car that has had regular wheel alignments.

As you can see, there are many reasons why a car owner should be sure to get regular wheel alignments. Not only does having your wheels aligned properly save you money on gas, tires, and other potential repairs, but it also gives you better peace of mind to know that your car is being cared for properly.

Andy West is a freelance writer for DAE, which offers wheel alignments and domestic automotive maintenance in the Houston area.

By Andy West

Basic problems of your car-How to save cost in car repair

2008-12-02T19:13:00.004+08:00

I used to be a truck driver, truck driving instructor, and an owner/operator of a big rig. I was also in the Army for 21 years, and in both areas, I learned an important technique which has been around a long time to save lots of money for huge organizations. The good news is that the same method can be used by anyone who owns a car, truck, motorcycle, RV, or any other type of vehicle.

These organizations use a preventive maintenance program to save them money on costly...really costly...vehicle repairs.

If you want to know how to save money on car repairs, just follow their lead.

All a preventive maintenance program is is the regular check of such things as condition and tightness of belts, condition of hoses, condition and pressure of tires, air and oil filters, and so on. One very important part of any such plan is regular oil changes.

A preventive maintenance program, which actually is probably outlined in your owner's manual, can keep your car running at near peak efficiency for years. Failure to check these items and repair or replace them at that time can result in very costly repairs at a later date.

For example, a simple oversight such as the failure to change your oil regularly can result in your needing to replace an entire engine! For a few minutes of your time every few months and few dollars out of pocket, you can save possible repairs costing thousands of dollars later!

As I pointed out, setting up a preventive maintenance program is easy as most of the info you need is in your owner's manual. If you do not have the owner's manual for your car or truck, it is easy to find the information you need online or at your local library. The actual points are easy. In fact, I pointed out most of them above.

By the way, although it might not result in repair costs, check headlights, tail lights, and turn signals regularly as well. This is not only for your safety and the safety of others, but it could prevent an accident or keep you from getting an expensive ticket.

How to save money on car repairs?

Simple. Stop the repair before it ever becomes needed.

Donovan Baldwin is a freelance writer living in Texas. A University Of West Florida alumnus (1973) with a BA in accounting, he is a member of Mensa and has held several managerial positions. After retiring from the U. S. Army in 1995, he became interested in internet marketing and developed various online businesses. He has been writing poetry, articles, and essays for over 40 years, and now frequently publishes articles on his own websites and for use by other webmasters. He is an authorized dealer for Amsoil synthetic motor oil and you can find his website at Lube2005.com.

By Donovan Baldwin